Pro potřebu kontaktu prosím využijte náš kontakt. Těšíme se na Vás

Nadporučík Jakub Pros

+420 777 964 736

E-MAIL:

INFO@MEMORIALPARASUTISTU.CZ

 

ADRESA:

Brána 200 metrů JZ od Škroupova 601, Chrudim
49.9413753N, 15.7811700E

Instagram

And this is employed and appearing good when I disconnect the OEM front side Center Speaker(Boston 2 Ohm middle)

And this is employed and appearing good when I disconnect the OEM front side Center Speaker(Boston 2 Ohm middle)

And this is employed and appearing good when I disconnect the OEM front side Center Speaker(Boston 2 Ohm middle)

The Kenwood DDX9907XR mind unit can be linked utilising the RCA back and front music Preouts on the JL music JD400/4 RCA Inputs CH. 1&2 and CH. 3&4 plus the Kicker 46CSS654 remaining & best entry way speakers connected to the presenter Outputs(CH. 1&2) and also the Kicker 46CSC6934 leftover & right back deck speakers linked to the presenter Outputs(CH. 3&4).

Really don’t imagine I can change the OEM front side middle Speaker(Boston 2 Ohm Mid) using Kicker 47KSC2704 4 Ohm Mid and then leave they linked to the OEM Amp front side speaker output since the OEM is actually 2 Ohm output. Your point above, i do believe for this reason , it really is higher when it’s plugged in.

From further research( it appears like… choice 1… I can set a speaker L-Pad Attenuator regarding the positive speaker cable between your OEM Amp therefore the new Kicker 47KSC2704 4 Ohm middle and use the attenuator to suit the quantity using the entry way speakers Option 2… create a signal processor into the system, this looks top but I really don’t know just what otherwise I need to become and how to catch it all up. Solution 3… buy a special Amp that helps the 5 audio speaker create You will find. Do one also exists because the front middle presenter are a mid variety audio speaker. Alternative 4… something else.

Hey there Farrell

Question… the other solutions manage We have allowing you to connect the Kicker 47KSC2704 4 Ohm middle in to the brand-new system without using the OEM Amp?

I like to be careful with terminology as if not could make misunderstandings or bring tips that aren’t rather precise. In this instance, it is advisable to know that there’s really no such thing as a a€?truea€? center presenter until you’re utilizing a sign processor or audio noise method that provides an independent center station sign origin.

The matter here’s the center speaker need more amount and capacity to they than each speaker, meaning you’ll have to decrease a good quantity of power across a resistor to get the levels down

For instance, in car acoustics processors Dolby expert reasoning II can imitate a genuine center station [deriving center from music, not just L+R mono]) when a DTS or Dolby online alert just isn’t present. That’s how I utilized a center station my self.

What you are planning to carry out inside setup try generate a a€?center filla€? or a€?pseudo-center/monoa€? mono presenter arrangement. This article you linked to failed to quite clarify it just how i might has expected, as they’re mostly interested in how exactly to hook it up. AudioControl used to have an excellent white paper discussing exactly why L+R is really detrimental to stereo imaging but i can not believe it is, unfortuitously.

Anyway, for your set-up there is alot happening. Therefore to get at the a€?meat and potatoesa€? from it all:

a€? you can make use of a 4I© audio speaker because of the OEM 2I©. It is going to work okay, with 1/2 the effectiveness of a 2I© presenter. a€? you happen to be using both RCA and speaker-level signals which means the quantity may not be properly proportional often times. It’s best to utilize just one single or or the various other, perhaps not both transmission type. a€? The JL amp is actually bridgeable, and what might be finished is use tri-mode whilst was once known as in older times. That is simply wiring one audio speaker in bridged setting while 2 stereo speakers are also wired one per channel as typical.

I find *at minimum* -15dB is an excellent begin, which means you’ll need a some energy resistors of pretty big energy rating. Perhaps not useful, and they’re going to bring hot at high-power result additionally. (predicated on the things I bring checking using my https://besthookupwebsites.net/dating-over-60/ audio speaker L-pad calculator right here.)

Post a Comment